永济洗地机_合肥晟晖 - 888集团手机版登录-888电子游戏登录入口-888集团游戏手机版安卓

888集团手机版登录

<cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite>
  • <cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite>
  • <cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite><cite id="xz27z037ya"></cite>
  • 欢迎来到合肥晟晖清洁产品商城
    合肥晟晖>资讯>手推式扫地车

    永济洗地机

    文章来源: 作者: 发布时间:2020年05月20日 点击数: 字号:

    洗地机重要的部位常规怎样检查

    How to check the important parts of the washing machine

    1)检查驾驶式洗地机离合器踏板自由行程,如果自由行程过大则进行调整。对于液压操纵机构检查是否贮液罐油量不足或管路中有空气,并进行必要的排除;

    1) Check the free travel of the clutch pedal of the driving washer, and adjust it if the free travel is too large. Check whether there is insufficient oil in the reservoir or air in the pipeline for the hydraulic control mechanism, and remove it if necessary;

    2)检查驾驶式洗地机分离杠杆内端高度,如果分离杠杆高度太低或不在同一平面,则进行调整;

    2) Check the height of the inner end of the release lever of the driving washing machine. If the height of the release lever is too low or not in the same plane, adjust it;

    3)检查驾驶式洗地机从动盘是否翘曲变形、铆钉脱落,从动盘是否轴向运动卡滞等,如果是,则进行更换或修理

    3) Check whether the driven plate of the driving washing machine is warped, deformed, rivets fall off, and whether the driven plate is stuck in axial movement. If so, replace or repair it

    洗地机发动机的活塞装置注意事项:

    Precautions for piston device of washing machine engine:

    洗地机的发动机在装置活塞时,应该先将活塞放在90度左右的机油中加热数分钟,再将其与连杆小头的装置孔对齐,把活塞销轻轻地推进装置孔内。而后将活塞销孔两端的卡簧槽内装上卡簧,再将活塞环装上。过细,应先装衬环与油环,再装第二、第一道气环。

    When installing the piston in the engine of the washing machine, first heat the piston in the oil of about 90 degrees for several minutes, then align it with the device hole of the small end of the connecting rod, and gently push the piston pin into the device hole. Then install the circlip in the circlip groove at both ends of the piston pin hole, and then install the piston ring. If it is too thin, first install the lining ring and oil ring, and then install the second and first gas rings.

    装置好活塞环后,应用手抓住活塞环外圆在环槽内旋动,查抄有无卡阻以为。同时,应在所装的活塞环涂抹机油,使机油匀称地散布到活塞环槽内。安置时,洗地机要连结活塞与活塞环表面的干净度,警备尘土沾到活塞的外貌。对设有装置偏向标志的活塞,应按标志装置,不要将偏向装错。

    After installing the piston ring, hold the outer circle of the piston ring by hand and rotate it in the ring groove to check whether there is any jamming. At the same time, the installed piston ring should be coated with oil, so that the oil is evenly distributed into the piston ring groove. When installing, the washer should keep the piston and the piston ring clean, and be aware of the appearance of the piston stained with dust. For the piston with device deviation sign, it shall be installed according to the sign device, and the deviation shall not be installed wrongly.